This Week's Most Remarkable Stories About Fiat Panda Key Fob Replacement
Reasons Your Fiat 500 Key Fob Won't Work
A fiat 500 key fob is a great way to unlock the doors and get started the car. There are many reasons why the fob may stop working. It could be due to a dead battery or damage to the receiver module, water issues, or interference.
This listing is for an NEW replacement Fiat Flip Key Remote that is similar to the Ilco brand. It has to be professionally programmed (click here to search for local locksmiths for automotive locksmiths). Includes lock, unlock, and trunk buttons.
Dead Coin Battery
A dead battery is the most common reason for your 500 key fob that isn't working. Modern key fobs come with a limited operating range, and must be within just a few feet of the vehicle to operate. If you are far from your vehicle when you press the key fob button the car won't be able to respond, and will display an "Key Fob Not Detected" message in the instrument cluster.
If this happens, simply replace the battery in the coin cell (Part number CR2032) with a fresh one from a reputable manufacturer like Panasonic, Duracell, or Energizer. You can typically find them at your local hardware store, or online.
After you've replaced the coin cell battery you can test it by standing next to your Fiat 500 and pressing the buttons. The parking lights will flash and the key fob will operate the lock and unlock switches.
If the key fob doesn't work after replacing the battery, it may be damaged by water, which prevents it from communicating with the receiver module inside your vehicle. Water damage can happen in many ways, including simply splashing or submerging the key fob saltwater at the beach. If you suspect that your fob has been exposed to water, you can place it in a bag of rice to draw out the moisture. If that doesn't work your fob will probably require reprogramming by a professional auto locksmith or the dealer.
Water Damage
Water damage can occur if you immerse the fob into the ocean or wash it in a machine. Saltwater can cause the circuit board to short and then cease to function. Getting the fob wet is not an ideal choice however, if you drop it in a cup of water or don't remember to take it out of your pocket before you run the washer Don't give up hope.
First, remove the battery. Before replacing the battery, clean the electronic chip with isopropyl, or a similar product. Check the fob again to see if it is working. If the key isn't working it could need to be reprogrammed. This is usually done by an auto locksmith or dealer.
If your key is older and is not programmed for your car You will need to replace it completely. This is a simple procedure that can be handled by a professional automotive locksmith. The locksmith will have to cut the key to match the ignition in your vehicle. The locksmith also needs to reprogram your fob into the vehicle's system. replacement fiat 500 key fob is a simple and affordable process which can be completed within the next day.
Receiver Module Issues
One of the main reasons why your 500 key fob may stop functioning is because it's out of range. The remote has a maximum range of 30 feet. So in the event that you are far away from your vehicle it won't respond to your commands. It is possible to fix this by moving the remote closer to your car until it responds.
If your fob does not work after you replace the battery inside the coin, which is also called a "button", "watch" or "button" or "button", it could be a problem with the circuit board inside. In the majority of cases, reprogramming your fob will solve the problem. The instructions are available for the majority of vehicles on YouTube or in the owner's guide.
It could be necessary to replace the clips made of metal that hold the coin batteries in place. If they lose tension it could hinder the coin battery from sitting properly and cause your remote to malfunction.
In rare cases the fob might be out of sync with your vehicle because of hardware or software problems. You can fix this issue by visiting your local auto-locksmith or dealer to reprogram your key fob. In some cases, the software may also require reinstallation into your body control modules.
Interference
Interference can also cause the key fob to not receive or transmit signals. This can happen when the key fob is located near the radio transmitter (cell phones, radar detectors) or another source of electromagnetic radiation. The key fob may not work due to a bad connection with the buttons or water damage, or damage to the internal chips.
If the key fob failed to work one day in the middle of the night and you've tried everything you can at home to fix it e.g. You might have a damaged 500 receiver module if you've tried replacing the battery, reprogramming it, or using a spare key fob. The receiver module is situated under the dash, and it picks up the radio frequency signals from the key fob. It converts them to electronic commands that the vehicle interprets.
There is a simple way to reset the 500's on-board system including the keyfob. Disconnect the battery for 15 minutes, removing first the negative cable and then the positive cable. Reconnect the battery. This will get rid of any remaining electricity and restart the car's computers, which could help the key fob to function again. If the issue continues it is recommended that you consult an expert certified technician. They can identify the exact cause of problems.